Skip to main content

mmal: mmal_vc_component_enable: failed to enable component: ENOSPC

This is a nasty bug with the Raspberry Pi camera module, which has not been resolved. Although I cannot guarantee that my solution will work for you, it fortunately did the trick for me.
  1. sudo apt-get update && sudo apt-get dist-upgrade  
  2. sudo rpi-update  

Make sure your  /etc/modprobe.d/raspi-blacklist.conf looks like this.


  1. sudo nano /etc/modprobe.d/raspi-blacklist.conf  
# blacklist spi and i2c by default (many users don't need them)

#blacklist spi-bcm2708
blacklist i2c-bcm2708

My /etc/modules config

  1. sudo nano /etc/modules

 # /etc/modules: kernel modules to load at boot time.
#
# This file contains the names of kernel modules that should be loaded
# at boot time, one per line. Lines beginning with "#" are ignored.
# Parameters can be specified after the module name.


w1-gpio pullup=1
w1-therm
i2c-bcm2708
i2c-dev
spi-bcm2708
snd-bcm2835
lirc_dev
lirc_rpi gpio_out_pin=7

Test

  1. sudo reboot  
  2. raspistill -v -o image.jpg  

Sample output

raspistill Camera App v1.3.8

Width 2592, Height 1944, quality 85, filename image.jpg
Time delay 5000, Raw no
Thumbnail enabled Yes, width 64, height 48, quality 35
Link to latest frame enabled  no
Full resolution preview No
Capture method : Single capture

Preview Yes, Full screen Yes
Preview window 0,0,1024,768
Opacity 255
Sharpness 0, Contrast 0, Brightness 50
Saturation 0, ISO 0, Video Stabilisation No, Exposure compensation 0
Exposure Mode 'auto', AWB Mode 'auto', Image Effect 'none'
Metering Mode 'average', Colour Effect Enabled No with U = 128, V = 128
Rotation 0, hflip No, vflip No
ROI x 0.000000, y 0.000000, w 1.000000 h 1.000000
Camera component done
Encoder component done
Starting component connection stage
Connecting camera preview port to video render.
Connecting camera stills port to encoder input port
Opening output file image.jpg
Enabling encoder output port
Starting capture 0
Finished capture 0
Closing down
Close down completed, all components disconnected, disabled and destroyed
Labels:

Comments

  1. Michał M15 May 2016 at 03:42

    Hello Mike M,

    Thank you so much this sharing! I tried to resolve the same problem for several days. I was sure the camera module was "fried" but then... I found your small tutorial : ). I'm so grateful for that!!

    Best greetings from Poland,
    Michał M.

    ReplyDelete
  2. Telmo30 September 2016 at 17:54

    I fuck*d up the operative system! Now I'll have the opportunity to get more experience installing everything over again! Thank you...

    ReplyDelete
  3. Unknown23 October 2017 at 00:07

    Nothing changed.Planning to install a fresh OS. Do you think that it will help ?

    ReplyDelete
  4. Unknown16 April 2018 at 09:57

    Nothing changed any other method

    ReplyDelete

Post a Comment

Popular posts from this blog

OsmocomBB - Hardware and Software Setup - Tutorial (Motorola C118)

OsmocomBB is an Open Source GSM Baseband software implementation. By using the sofware on a compatible phone (e.g. Motorola C118), you are able to make and receive phone calls, send and receive SMS, etc. based on Free Software only.       Hardware PL2303HX USB Serial To RS232 TTL Chip 2.5 mm audio jack Motorola C118 (E88) This is a typical pin-out of a 2.5 mm audio jack: L (Left Signal) Tip 1 Green R (Right Signal) Ring 2 Red GND (Ground) Sleeve 3 Bare Copper You need to soldier the 2.5mm audio jack to the USB Serial To RS232 TTL Chip, whereas TxD is at the tip of the plug RxD is at the middle contact GND is the outer contact  Software Connect the phone to your PC and check if it is being recognized. dmesg | grep tty user@user:~$ dmesg | grep tty [    0.000000] console [tty0] enabled [ 6522.143379] usb 3-2: pl2303 converter now attached to ttyUSB0 To make sure everything is working, install cu and c
9 comments
Read more

Scid vs PC installation guide - Ubuntu (Mint, Debian etc.)

Scid vs PC Scid vs PC is definitely the best and most comprehensive chess software for Linux.  Unfortunately I struggled quite a bit to get it up and running. Before I start: You might prefer to watch the video. Otherwise keep on reading. Open a terminal and execute the following commands sudo apt-get install auto-apt build-essential sudo auto-apt update-local sudo auto-apt update sudo auto-apt updatedb Now make sure you got both tcl8.5-dev and tk8.5-dev installed sudo apt-get install tcl8.5-dev tcl8.5 sudo apt-get install tk8.5-dev tk8.5 Some users are reporting problems on Ubuntu 14.04. sudo apt-get install tcl8.6-dev tcl8.6 sudo apt-get install tk8.6-dev tk8.6 libgcj15-dev The 'x' refers to the current release: e.g. 4.9.tgz download scid vs pc: http://sourceforge.net/projects/scidvspc/files/source/scid_vs_pc-4.9.tgz/download tar -xzf scid_vs_pc-4.xx.tgz cd scid_vs_pc-4.x sudo auto-apt run ./configure sudo auto-apt run make sudo auto-apt run make install
36 comments
Read more

Banana Pi: Temperature Sensor (DS18B20) - Tutorial

Requirements --> Banana Pi running Raspbian for Banana Pi --> Breadboard --> Jumper Wires --> DS18b20 --> 4.7K Ohm resistor --> Breakout cobbler   Hardware Setup Refer to the graphic for the correct wiring. Make sure the Banana Pi is switched off to prevent any possible damage. Software Setup Double check the wiring and boot the device. In order to be able to access the temperature data, we need to make some minor adjustments to the script.bin file , which is a binary configuration file used by Allwinner SOC. sudo apt-get install git git clone https://github.com/linux-sunxi/sunxi-tools cd sunxi-tools make #location of the script.bin file cd /boot/bananapi/ #get the fex file sudo /home/bananapi/sunxi-tools/bin2fex script.bin bananapi.fex #edit the fex file sudo nano bananapi.fex #add the following at the end, save (CTRL + O) and close [w1_para] gpio = 4 #.fex back to .bin sudo /home/bananapi/sunxi-tools/fex2bin bananapi.fex script.bin sud
14 comments
Read more